CARDAX 6000 PDF

Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Vigis Nikomi
Country: Papua New Guinea
Language: English (Spanish)
Genre: Literature
Published (Last): 17 September 2004
Pages: 234
PDF File Size: 11.39 Mb
ePub File Size: 2.4 Mb
ISBN: 284-4-94617-636-9
Downloads: 40294
Price: Free* [*Free Regsitration Required]
Uploader: Fenrimuro

When the Cardax FT Controller is re-powered after servicing and is operating correctly, the optical tamper detectors will be re-initialised.

Gallagher Controllers | AES Group Ltd.

The In-service relay is used to signal an external alarm if the Controller fails. Unused For factory testing only. Providing flexible configuration options to meet specific site requirements, Gallagher Controllers:. Operation 66000 this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. On startup, the main application is run.

Looking at the Controller it will be obvious that the there is no ethernet activity on either ethernet connection, as the RJ45 connector LEDs will not be operating, and the Controllers run LED will be in 2 flash.

The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in brackets: Follow the steps below to access the Controller’s Config web page: Note that this cable type is only suitable for the communications circuits.

On-board connections are provided for:. Controller The Gallagher Controller is specifically designed to support access controlled doors and integrated intruder alarms. Changes or modifications not expressly approved by Gallagher Security Management Systems could void the user’s authority to operate this equipment.

  COMPUTATIONAL PHYSICS FORTRAN VERSION STEVEN E.KOONIN PDF

Cardax Ft Controller 6000pdf

The termination jumper on either GBUS circuit needs to be fitted if the Controller is the end device for this circuit. The Cabinet door must remain closed for at least one minute for the initialisation of the optical tamper detectors to be completed. The section titled “Run LED” later in this Installation Note details the different meanings of the various flash sequences. Ensure 60000 the power to the Cardax FT Controller is switched off and disconnected.

Communication between Cardax FT Controllers and lower level hardware items uses two Cardax-proprietary data communication formats. This picture is not to scale, therefore use the measurements provided. In the event of a catastrophic failure, after approximately 60 seconds the In-Service relay opens. Cardax FT Version 5. Turn on the power supply. On startup configuration and the IP address is deleted.

Cardax Ft Controller pdf

Click the OK button. Install all cardsx system and power cables. Cardax FT Key Strengths. However, this DC voltage out will be approximately 1 volt lower than the voltage supplied to the Cardax FT Controller This means in the event of network communications being disrupted, security is maintained on site.

cardwx There is a proprietary serial communication protocol between the two boards. The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in brackets:. Purpose of this presentation This presentation introduces: The red Run LED flashes in the following sequence: 0600 both you and the equipment are earthed before beginning any servicing.!

  EJERCICIOS DE FACTORIZACION RESUELTOS PDF

Then, as it has no configuration, it will not connect to the FT server until the primary ethernet link is connected. On-board termination is optional using termination jumpers. The security of the installation ultimately depends on the way the Cardax FT Cabinet is installed.

Part number 3E R1 August Carefully lift the Controller clear of the Cabinet.

This decal enables you to enter wiring and connection details and identifies the location and designation of cable connections, Cradax, etc. Normal Startup – Configuration will be retained.

Revert to the factory default version of the operating system. On-board connections are provided for: The Cardax FT Controller integrates much of the functionality of the original Integrated Access Control and Intruder Alarms capability 2. Both units are designed to fit into a standard Cardax FT Cabinet together.

Cardax FT for Airport Security. The following procedure will ensure that the optical tamper sensors are initialised correctly on power-up.

Cardax FT Controller Documents. Plug-in ModemThe Cardax FT Controller has an on-board connector Serial for a plugin modem part number C which is purchased separately from the Controller Assigning an IP address manually via a web browser When the Cardax FT Controller is started reset or power-up with DIP switches 2 and 3 enabled, the Controller uses the following default addresses: